Tutorial Cara Install Modem SmartFren ce682 di Linux Ubuntu dengan Wvdial

Denger denger sih modem smartfren katanya gak mau terdeteksi di ubuntu, tapi saya juga tidak tau benar atau tidak, soalnya saya belum pernah mencobanya, nah tadi saat sedang jalan-jalan di forum devilzc0de saya melihat threadnya om jedag jedug  yang berbagi pengalaman pribadi install modem Smartfren ce682 di ubuntu.

Ok jika mau praktek silakan ikuti tutorialnya.
pertama cek dulu dmsegnya dengan perintah "dmesg | tail" tanpa tanda kutip. Hasilnya akan keluar begini :

syarhil@aquarel-lapy:~$ dmesg | tail
[ 16.435959] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 19.963390] EXT4-fs (sda7): re-mounted. Opts: errors=remount-ro,commit=0
[ 19.966436] EXT4-fs (sda8): re-mounted. Opts: commit=0
[ 241.704054] usb 2-2: USB disconnect, address 3
[ 253.352033] usb 2-2: new full speed USB device using uhci_hcd and address 4
[ 253.522675] scsi5 : usb-storage 2-2:1.0
[ 254.524252] scsi 5:0:0:0: CD-ROM CDROM EVDO ReV A 7.00 PQ: 0 ANSI: 2
[ 254.536216] sr1: scsi-1 drive
[ 254.536454] sr 5:0:0:0: Attached scsi CD-ROM sr1
[ 254.536652] sr 5:0:0:0: Attached scsi generic sg2 type 5

kemudian eject dulu cdrom nya dengan perintah  :

sudo eject /dev/sr1

setelah itu lihat lagi dmesg nya dengan perintah di atas, hasilnya akan menjadi :

syarhil@aquarel-lapy:~$ dmesg | tail
[ 254.524252] scsi 5:0:0:0: CD-ROM CDROM EVDO ReV A 7.00 PQ: 0 ANSI: 2
[ 254.536216] sr1: scsi-1 drive
[ 254.536454] sr 5:0:0:0: Attached scsi CD-ROM sr1
[ 254.536652] sr 5:0:0:0: Attached scsi generic sg2 type 5
[ 365.648085] usb 2-2: USB disconnect, address 4
[ 368.192038] usb 2-2: new full speed USB device using uhci_hcd and address 5
[ 368.375134] scsi6 : usb-storage 2-2:1.3
[ 369.380301] scsi 6:0:0:0: Direct-Access SDVDISK EVDO ReV A 7.00 PQ: 0 ANSI: 0 CCS
[ 369.381257] sd 6:0:0:0: Attached scsi generic sg2 type 0
[ 369.473277] sd 6:0:0:0: [sdb] Attached SCSI removable disk

kemudian cek modemnya dengan perintah "lsusb" tanpa tanda kutip:

syarhil@aquarel-lapy:~$ lsusb
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 005: ID 201e:1022
Bus 002 Device 002: ID 15ca:00c3 Textech International Ltd. Mini Optical Mouse
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub

ternyata terdetect dengan vendor dan product idnya,Bus 002 Device 005: ID 201e:1022
tapi nama vendornya ga muncul, ga masalah tetep lanjut
sekarang ke pengaturan, masuk ke :

sudo gedit /etc/usb_modeswitch.conf

tambahkan kode dibawah ke baris yang paling akhir :

# /etc/usb_modeswitch.conf
#
# Smart Haier CE682 (EVDO)
#
DefaultVendor = 0x201e
DefaultProduct = 0×1022
TargetVendor = 00x201e
TargetProduct = 0×1022
MessageContent=”5553424312345678c00000008000069f030000000000000000000000000000″

masuk lagi ke :

sudo gedit /etc/udev/rules.d/99-haier-ce682.rules

isi dengan :

# /etc/udev/rules.d/99-zte-ce682.rules
#
# Smart Haier CE682 (EVDO)
#
SUBSYSTEM==”usb”, SYSFS{idVendor}==”201e”,

SYSFS{idProduct}==”1022″, RUN+=”/usr/sbin/usb_modeswitch –default-vendor 0x201e –default-product 0×1022 –message-content 5553424312345678c00000008000069f030000000000000000000000000000″

lalu savesekarang load beberapa parameter yang dibutuhkan ke kernel

sudo modprobe usbserial vendor=0X201e product=0X1022

Install deteksi modemnya dengan perintah :

sudo apt-get install wvdial

syarhil@aquarel-lapy:~$ sudo wvdialconf
Editing `/etc/wvdial.conf’.
Scanning your serial ports for a modem.
ttyS0: ATQ0 V1 E1 — failed with 2400 baud, next try: 9600 baud
ttyS0: ATQ0 V1 E1 — failed with 9600 baud, next try: 115200 baud
ttyS0: ATQ0 V1 E1 — and failed too at 115200, giving up.
ttyS1: ATQ0 V1 E1 — failed with 2400 baud, next try: 9600 baud
ttyS1: ATQ0 V1 E1 — failed with 9600 baud, next try: 115200 baud
ttyS1: ATQ0 V1 E1 — and failed too at 115200, giving up.
Modem Port Scan: S2 S3 S4 S5 S6 S7 S8 S9
Modem Port Scan: S10 S11 S12 S13 S14 S15 S16 S17
Modem Port Scan: S18 S19 S20 S21 S22 S23 S24 S25
Modem Port Scan: S26 S27 S28 S29 S30 S31
WvModem: Cannot get information for serial port.
ttyUSB0: ATQ0 V1 E1 — OK
ttyUSB0: ATQ0 V1 E1 Z — OK
ttyUSB0: ATQ0 V1 E1 S0=0 — OK
ttyUSB0: ATQ0 V1 E1 S0=0 &C1 — OK
ttyUSB0: ATQ0 V1 E1 S0=0 &C1 &D2 — OK
ttyUSB0: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 — OK
ttyUSB0: Modem Identifier: ATI — Manufacturer: +GMI: China TeleCom
ttyUSB0: Speed 9600: AT — OK
ttyUSB0: Max speed is 9600; that should be safe.
ttyUSB0: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 — OK
WvModem: Cannot get information for serial port.
ttyUSB1: ATQ0 V1 E1 — failed with 2400 baud, next try: 9600 baud
ttyUSB1: ATQ0 V1 E1 — failed with 9600 baud, next try: 9600 baud
ttyUSB1: ATQ0 V1 E1 — and failed too at 115200, giving up.
WvModem: Cannot get information for serial port.
ttyUSB2: ATQ0 V1 E1 — OK
ttyUSB2: ATQ0 V1 E1 Z — OK
ttyUSB2: ATQ0 V1 E1 S0=0 — OK
ttyUSB2: ATQ0 V1 E1 S0=0 &C1 — OK
ttyUSB2: ATQ0 V1 E1 S0=0 &C1 &D2 — OK
ttyUSB2: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 — OK
ttyUSB2: Modem Identifier: ATI — Manufacturer: +GMI: China TeleCom
ttyUSB2: Speed 9600: AT — OK
ttyUSB2: Max speed is 9600; that should be safe.
ttyUSB2: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 — OK
Found a modem on /dev/ttyUSB0.
Modem configuration written to /etc/wvdial.conf.
ttyUSB0: Speed 9600; init “ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0″
ttyUSB2: Speed 9600; init “ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0″

modem terdeteksi di /dev/ttyUSB0lanjut ke pengaturan wvdial
masuk ke :

sudo gedit /etc/wvdial.conf

tambah baris berikut :

[Dialer smart]Init1 = ATZ
Init2 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
Stupid Mode = 1
Modem Type = Analog Modem
Command Line = ATDT
ISDN = 0
New PPPD = yes
Phone = #777
Modem = /dev/ttyUSB0
Username = smart
Password = smart
Baud = 460800

langkah terakhir coba koneksikan dengan perintah :

sudo wvdial smart

Jika sudah mendapat ip address diatas harusnya sudah bisa browsing internet. Sekarang masalahnya setiap mau connect, modem kita colokkan, kita harus eject cd rom, load kernel dll, nah biar cepat kita buat launcher bash script, buat file baru ekstensi .sh, isi seperti berikut :

#!/bin/bash
sudo eject /dev/sr1
sleep 2
sudo modprobe usbserial vendor=0X201e product=0X1022
sleep 2
sudo wvdial smart

rubah permissionnnya dulu agar bisa dijalankan :

sudo chmod +x smart.sh

untuk menjalankan tinggal ketik :

./smart.sh

Selamat mencoba semoga sukses!

sumber:  http://www.thedexwan.net/2012/02/instal-modem-smartfren-ce682-di-ubuntu.html